Difference between revisions of "IP PBX Manual Destinations Groups"

From IPitomy Wiki
Jump to navigation Jump to search
m
 
(One intermediate revision by the same user not shown)
Line 10: Line 10:
  
 
For example, a business might create a few user Groups in an IP telephony network, e.g. Sales, Marketing, Administration, Accounting, Engineering, etc. Groups may also be created for people in similar locations like a plant floor, the north section of a building or the front office. The goal of a group is to ring telephones based on the incoming routing logic (e.g. DIDs, Auto Attendant selected by the incoming caller, or time of day). Note that calls routing to an extension from a ring group will ignore that phones PBX forwarding settings. Some phones have forwarding settings which are independent of the PBX (not set through the PBX Web GUI). These settings will still be applied.
 
For example, a business might create a few user Groups in an IP telephony network, e.g. Sales, Marketing, Administration, Accounting, Engineering, etc. Groups may also be created for people in similar locations like a plant floor, the north section of a building or the front office. The goal of a group is to ring telephones based on the incoming routing logic (e.g. DIDs, Auto Attendant selected by the incoming caller, or time of day). Note that calls routing to an extension from a ring group will ignore that phones PBX forwarding settings. Some phones have forwarding settings which are independent of the PBX (not set through the PBX Web GUI). These settings will still be applied.
 +
 +
WARNING:  A busy system WILL start to experience slow down when using more than 20 queues.  This is due to the system calculating statistics for all queues, on a live basis.  This can be alleviated by using the option on PBXSetup->Services to Suppress Call/Queue Manager statistics and disable RNA Statistics.
  
 
*Link to [https://www.youtube.com/watch?v=dZavlZJW-18&feature=c4-overview&list=UU1cwHaNWU97sdZm3yEBqNeg <u>'''''Ring'''''</u>&nbsp;<u>'''''Group'''''</u>] training video - [https://www.youtube.com/watch?v=dZavlZJW-18&feature=c4-overview&list=UU1cwHaNWU97sdZm3yEBqNeg [1]]
 
*Link to [https://www.youtube.com/watch?v=dZavlZJW-18&feature=c4-overview&list=UU1cwHaNWU97sdZm3yEBqNeg <u>'''''Ring'''''</u>&nbsp;<u>'''''Group'''''</u>] training video - [https://www.youtube.com/watch?v=dZavlZJW-18&feature=c4-overview&list=UU1cwHaNWU97sdZm3yEBqNeg [1]]
Line 476: Line 478:
 
'''NOTE: IPitomy recommends using multicast paging for groups of 10 or more phones that are paged frequently.''' [[File:Multicastgroups.png|center|Multicastgroups.png]] [[File:Editmultipagewindow.png|center|Editmultipagewindow.png]]<br/>The following table describes the fields (parameters) on the Multicast Edit Paging Group window and the recommended settings.
 
'''NOTE: IPitomy recommends using multicast paging for groups of 10 or more phones that are paged frequently.''' [[File:Multicastgroups.png|center|Multicastgroups.png]] [[File:Editmultipagewindow.png|center|Editmultipagewindow.png]]<br/>The following table describes the fields (parameters) on the Multicast Edit Paging Group window and the recommended settings.
  
WARNING: Multicast paging DOES NOT WORK from a cloud pbx.  In order to simulate multicast paging from cloud, additional specialized hardware will be required, and is not supported directly by IPitomy.
+
'''WARNING: Multicast paging DOES NOT WORK from a cloud pbx.  In order to simulate multicast paging from cloud, additional specialized hardware will be required, and is not supported directly by IPitomy.'''
  
  

Latest revision as of 20:11, 20 October 2016



Logo on white background (small).gif
support@ipitomy.com | 941.306.2200 (Opt 2 for Support)
You are viewing the IPitomy IP PBX Manual, Table of Contents.


Groups

A Group is a logical grouping of extensions and their privileges. Each Group is associated with a set of PBX features and call routing strategies. It is advised to build the extensions in the PBX first, allowing the groups to be populated at the time of creation.

These Groups allow incoming calls to be distributed to a group of extensions rather than just one extension. Within the Groups, different distribution strategies may be selected based on the call coverage required by the application. Groups also provide off-hook paging functionality. By dialing the intercom button or code followed by the group number, extensions in the group will receive the page over the intercom. Groups are a set of extensions that are related either because they:

  • Serve a similar business function.
  • Work within the same department.
  • Are located in proximity to each other.

For example, a business might create a few user Groups in an IP telephony network, e.g. Sales, Marketing, Administration, Accounting, Engineering, etc. Groups may also be created for people in similar locations like a plant floor, the north section of a building or the front office. The goal of a group is to ring telephones based on the incoming routing logic (e.g. DIDs, Auto Attendant selected by the incoming caller, or time of day). Note that calls routing to an extension from a ring group will ignore that phones PBX forwarding settings. Some phones have forwarding settings which are independent of the PBX (not set through the PBX Web GUI). These settings will still be applied.

WARNING: A busy system WILL start to experience slow down when using more than 20 queues. This is due to the system calculating statistics for all queues, on a live basis. This can be alleviated by using the option on PBXSetup->Services to Suppress Call/Queue Manager statistics and disable RNA Statistics.

Ringgroupspages.png

Ring Group Examples

Ring groups define a set of extensions (people) that answer calls. Ring groups can be created for departments (e.g. Sales, Engineering) or buisiness regions (e.g. north, south, etc), or areas of a business (e.g. a warehouse or plant floor). These ring groups can appear on an Automated Attendant (menu). When the group is selected from a Menu, the call is routed to the group. These calls will be distributed to the member extensions based upon the ring strategy for the group. The ring strategy for the group can be set from the drop-down list. Available call distribution options are:

  • Ring AllRing all extensions in the group simultaneously
  • Round RobinTake turns ringing each extension, starts at the first extension for each new call
  • Round Robin (with memory)Take turns ringing each extension, starts where the last call left off
  • Least RecentRing extensions in order of which was least recently called by the queue. If using agents, logging out will reset the call counter so the next time that agent logs in, they will be at the top of the list for queue calls.
  • Fewest CallsRing extension in order of which has the fewest completed calls from the queue
  • RandomRandomly ring one extension at a time

Example Ring Group 1Departmental Grouping

Ring group definitions can be found in the Add a New Ring Group section of this guide. If a business has the following departments and people: This business can setup the following ring groups supporting business operations.


GROUP 1 - Sales Ext. GROUP 2Customer Services Ext.
Cathy Caldwell 123 Gretchen Goodall 134
David Dawson 124 Peter Polk 135
Susan Smith 125
Robert Reed 126

Using this ring group scenario the Menu would look like:

  • Sales (Destination - Group 1).
  • Customer Service (Destination - Group 2).
  • Office Manager (Destination - Ext. 113).

The menu prompt (message) for this menu and group arrangement would read as follows:

“Thank you for calling CompanyA, a leading manufacturer of cable assemblies and wiring harnesses. If you know the extension of the party you would like to reach you may dial it at any time.”

  • For Sales, press 1.
  • For Customer Service, press 2.
  • For Accounting, press 3.

Once a call is sent to Sales, member extension will be rang according to the ring group strategy.

Example Ring Group 2Regional Sales Grouping

GROUP 1 East Coast Sales Ext. GROUP 2 -West Coast Sales Ext. GROUP 3 Customer Service Ext.
Cathy Caldwell 123 Susan Smith 125 Gretchen Goodall 134
David Dawson 124 Robert Reed 126 Peter Polk 135

Using this ring group scenario the Menu would look like:

  • East Coast Sales (Destination - Group 1).
  • West Coast Sales (Destination - Group 2).
  • Customer Service (Destination - Group 3).
  • Office Manager (Destination - Ext. 113).

The menu prompt for this menu and group arrangement would read as follows:

“Thank you for calling CompanyA, a leading manufacturer of cable assemblies and wiring harnesses. If you know the extension of the party you would like to reach you may dial it at any time. For”

  • East Coast Sales, press 1.
  • West Coast Sales, press 2.
  • Customer Service, press 3.
  • Accounting, press 4.

Calls sent to these groups might use different ring strategies. The East Coast Sales group might answer calls Round Robin, distributing the calls to each Sale Representative consecutively. If a sales person is missing from the West Coast team this group might set phones to Ring All in the group so that calls don’t get missed. The Customer Service team may get high volumes of calls during a specified period of time, so this group may be set to ring Least Recent.

Add/Edit New Ring Group

Editringgroup.png

The following table describes the parameters (fields) on the Edit Ring Group page and their descriptions and recommended settings.


Sections/Fields
Description
Name
The name associated with this ring group.
 Group Number (to dial group)
The number dialed to access this ring group. Must be 3 or 4 digits.
Allow Paging with **+Group Number
If enabled (checked), this will allow **+ group number to page this ring group
Ring Strategy
This defines how calls are distributed to member extensions. Options are:

Ring All - Ring all extensions in the group simultaneously

Round Robin - Ring extensions consecutively. Delivers a new call to the first person in the group only after the last person in the group has taken a call. If an extension is busy the call will automatically be routed to the next extension in the group.

Round Robin (with memory) - Ring extensions consecutively. Delivers a new call to the first person in the group only after the last person in the group has taken a call. Remembers where the last call was taken and distributes new calls to the next extension in the rotation.

Least Recent - Ring extensions in order of which was least recently called by the queue.

Fewest Calls - Ring extension in order of which has the fewest completed calls from the queue

Random - Distributes calls randomly to the group.

Failover Destination
This defines where a call will be sent when it goes unanswered for a duration that matches the Timeout for the group.
Timeout
Defines, in seconds, the total time a call will spend in the ring group before being sent to the Failover Destination
Allow Recording
Determines if feature code recording is allowed for calls in this queue.

If YES = enables the recording feature.

If NO = disables the recording feature.

Agent Ring Time
Defines, in seconds, how long the queue will ring a particular agent. If using the Ring All strategy, this value should match the Timeout. For other strategies, this should be set to how long an extension should ring before moving on to the next.
Autofill

This deals with how the queue handles multiple concurrent calls. If set to NO the queue will wait until the first call is answered before ringing phones with the second call. If set to YES the queue will ring phones for all calls as they come in.  Note this setting has a different effect with ring all that may not be desirable. 

When autofill is yes and ring strategy is 'ringall' the group will still deliver the calls in the order they are received and in order to prevent calls from being lost by phones that have too few lines for the number of calls in the queue, the group will only deliver a single additional call when Ring In Use is set to yes. If someone who's phone is ringing rejects the call, the group will deliver the next call in line to all members.  This means the the rejected call is no longer ringing the member's phone that rejected the call, however it is still ringing all of the other members.  At the same time the 2nd call in line comes in and rings everyone.

Ring In use
If YES = Distribute calls to group members if they are already on a call

If NO = Do NOT distribute calls to group members if they are already on a call

The following outlines the steps to add/edit ring group settings.

STEPS:

  1. From the Destinations=>Group page, click the ADD Group button. The Edit Ring Group page appears.
  2. In the Name field, enter a name for the group.
  3. In the Group Number field, enter a number for the group. This number must be three or four digits in length.
  4. Check the Allow Paging with **+ the Group Number to enable the setting.
  5. Select the desired Ring Strategy from the drop-down list.
  6. Select the desired Failover Destination from the list of available options.
  7. Enter the time for the Timeout parameter.
  8. Select “Yes” if you want to enable the Allow Recording setting. Otherwise, set it to “No”.
  9. Enter the time for the Agent Ring Time parameter.
  10. Select “Yes” if you want to enable the Autofill setting. Otherwise, set it to “No
  11. Select “Yes” if you want to enable the Ring in use setting. Otherwise, set it to “No
  12. Click Savechanges.png the button.
  13. From the Members section of the Edit Ring Group page, select the extension number from the list of extensions that you want to add to the ring group. Click the ADD button.
  14. A second list appears next to the Members list displaying the selected extension. Repeat step 13 until all extensions that you want to add are on the list. Additionally, Shift or Control click functionality works for adding multiple extensions at once.
  15. To remove an item from the list of additions, select the extension number then click the REMOVE button.
  16. Define Priorities for the extensions, if needed. The scale ranges 0 thru 9 (0 is the highest priority).
  17. Click the Savechanges.png button to save the changes.
  18. Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

Ring Group Advanced Settings

Customcallerid.png

The following table describes the parameters (fields) on the Advanced Settings for Ring Groups page and their descriptions and recommended settings.


Sections/Fields
Description
Ring/Hold Settings
Caller Hears Ringing plays a ring tone to the caller, Music on Hold plays music to the caller.
Override Hold Music If set to yes, the Hold Music set here will play whenever this call goes on hold.  This ensures the same message is played, even if the extension that puts teh call on hold has its own custom MOH set.  If set to no, the Hold Music set in the group will not override another hold music.
Hold Music Set this to the Music on Hold play list you want heard for callers in this ring group.
Ring Tone When Caller Ring Settings are set to Ringing, use this to define the ring cadence.
Custom Caller ID Settings
Use Defines what method, if any, you wish to use to override Inbound CID. The options are:

System Default, Name, Number, Name and Number

Name This is the name of the caller that will be displayed when a call is received.
Number This is the number of the caller that will be displayed when a call is received.
Prepend Selecting Prepend will enter the text you put in the field, followed by the original CID. If not prepending, the override eliminates the original information.

Edit Advanced Ring Group Settings

STEPS:

  1. Select Destinations=>Groups. The Ring Groups page appears.
  2. Select the Ring Group you want to edit by either select the Penciledit.png icon to the right of the group name or click on the blue Group Name link.
  3. The Edit Ring Group page appears. Scroll down the page and click on the Advanced link. The Advanced Ring Group Settings section is displayed.
  4. Make the necessary changes to the settings then click button Savechanges.png to save the changes.
  5. Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

Edit Custom Caller ID Settings

STEPS:

  1. Select Destinations=>Groups. The Ring Groups page appears.
  2. Select the Ring Group you want to edit by either select the Penciledit.png icon to the right of the group name or click on the blue Group Name link.
  3. The Edit Ring Group page appears. Scroll down the page and click on the Advanced link. The Custom Caller ID section is displayed.
  4. Make the necessary changes to the settings then click Savechanges.png button to save the changes.
  5. Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

Edit Members/Agents

Editmembersagents.png
Sections/Fields
Description
Members This is the list of available extensions that are in the database.
Agents This is the list of available agents that are in the database.
Priority This field allows you to set the priority level for the members or agents. The lower the number, the higher the priority.
ADD This button will add the select item on the list to the right of the available members or agents. Shift and Control click functionality works for adding more than one at a time.
REMOVE This button will remove the item(s) that have been selected from the list of available members or agents. Shift and Control click functionality works for adding more than one at a time.

Add Agents/Members to the Group

STEPS:

  1. Navigate to the Destinations=>Groups=>Edit Group page.
  2. Select from the left hand column which agents/members to add to the group.
  3. Click the Add button.
  4. Click Savechanges.png button to save the changes.
  5. Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database

Delete Agents/Members from the Group

STEPS:

  1. STEPS: Navigate to the Destinations=>Groups=>Edit Group page.
  2. Select from the right hand column which agents/members to remove from the group.
  3. Click the Add button.
  4. Click Savechanges.png button to save the changes.
  5. Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database

Automatic Call Distribution (ACD)

Systems licensed to use ACD will have access to additional functionality pertaining to Ring Groups. ACD allows for more flexibility and control over the queuing in a Ring Group, as well as allowing the creation of Agents who can be added to the Ring Group.

Autocalldistpage.png

Sections/Fields
Description
Agent Retry Timer This defines, in seconds, how long the queue will wait before attempting to ring an agent again.
Weight The priority of the queue in relation to other queues in the system.
Wrap-up Time This defines, in seconds, how long the queue will wait after an agent has ended a call before flagging then as an active agent ready to accept more calls.
Autopause This will place an agent in a pause state in relation to this queue when they ignore or answer a call. To become an active member of the queue again unpause using the 1* feature code a phone or 1*+agent# for an agent.
Maximum # of people in queue Defines how many callers can join the queue before it is considered full.
Announce Frequency Must be set for Announce Holdtime to function. This pertains to how often the caller will hear the hold time announcement, in seconds
Periodic Announce Frequency This defines how much time passes between playing the recording that was set for this queue under Periodic Announcement.
Announce Holdtime If set to YES this will announce a caller’s status in the queue with regards to their expected hold time, pending the hold time is estimated to be over 1 minute. If the hold time is less than one minute, this will announce the caller’s position in the queue. A period of time is needed for the algorithm to ‘learn’ and estimate hold times accurately. This message will not play for the first caller in the queue. Caller Ring Settings must be set to a MOH file in order for this message to play.
Join Empty Queue Controls if a caller can join a queue.

YES = Callers can join the queue with no members or whose members are busy.

NO = Callers can only join the queue with active, non-busy members.

STRICT = Callers can join the queue as long as there are active members, be they available or busy.

Leave Empty Queue Controls if a caller will leave an empty queue.

YES = Callers will leave the queue if there are no active members, or all members are busy.

NO = Callers will not leave the queue even if there are no active members, or all members are busy.

STRICT = Callers will leave the queue if there are no active members, but will remain in the queue if all members are busy.

Report Hold Time Set to YES if you want the person answering the queue call to hear a message indicating how long the call they just answered was in the queue
Member Delay before connect Delay, in seconds, before a member is connected to the queue.
Timeout Restart If set to YES the ring group timeout will reset after attempting to ring an agent/member. When set to NO, time taken to ring an agent/member will be subtracted from the ring group time, and when the timer ends the group will send the caller to the Failover Destination
Service Level Set this to the time, in seconds, that defines the acceptable level of service for the queue. The Live Queue Data page will track the percentage of calls answered within the allotted time.
Exit Status: FULL

Exit Status: JOINEMPTY

Exit Status: LEAVEEMPTY

Exit Status: JOINUNAVAIL

Exit Status: LEAVEUNAVAIL

These are the destinations where calls will go based on the exit strategy defined. If no one in the group accepts the call this is the destination to which the call will be sent. Destinations can be extensions, other ring groups, a menu or a voicemail box.
Intro Announcement Define what prompt to play to the caller just before they enter the queue. (Previously “Announce Filename”)
Agent Announcement Defines what prompt to play to the agent/member who answers the queue call. This setting is set per Queue and therefore can be used to identify what Queue is being answered (for agents handling calls from multiple Queues.
Periodic Announcement Defines what prompt to play to the caller at the Periodic Announce frequency interval. This will not play for the caller in the first position of the queue. Caller Ring Settings must be set to a MOH file in order for this message to play.
Exit Menu Set this to a menu. Key presses while in this group will send people the corresponding destination from that menu.

Table 39Edit Ring Group ACD Agents Settings and Descriptions


Edit Automatic Call Distribution (ACD) Settings

STEPS:

  1. From the Destinations=>Groups=>Edit Group page, scroll to the ACD Settings section.
  2. Make the necessary updates to the ACD settings.
  3. Click Savechanges.png button to save the changes.
  4. Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

Add Automatic Call Distribution (ACD) Agents

Addeditagentfeatures.png

Sections/Fields
Description
Name Enter a name that will identify this agent.
ID Enter a unique 3-4 digit number to identify this agent. This number is used to log in/out.
PIN Enter a minimum of 4 digits for the PIN. This is the password used to log in/out with the agent.

Table 40Add/Edit Agent Features and Descriptions


STEPS:

  1. From the Destinations=>Groups=>Edit Group page, scroll to the ACD Settings section.
  2. Click on the blue Agents link to the right of the words ACD Settings. The Agents page appears.
  3. Click on the ADD button to add a new agent. A box with the name, ID and PIN field appears. Enter the information for the new agent.
  4. Click Savechanges.png button to save the changes.
  5. Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

PBX-Setup -> Agents


By navigation to PBX-Setup ->Agents the technician may access the agent creation page. On this page you may create agents for use in ACD Ring Groups. Each Agent requires a unique two digit ID and a Unique 4 Digit PIN. To create an agent enter the users Name, ID must be at least 2 digits and should not match their extension number and a 4 digit PIN and select Add. After this before exiting page you should also select Save Changes and the Apply these changes at the top of the page.



File:PBXSetup Agents.jpg


From this same page you can also access the ACD Queue Recordings page.


File:Queue Recordings.jpg


At this location you can listen to Agent Recordings. To download a recording click the download button. You may then play in any audio application. The delete button allows for deletion of files from the PBX. Agent recordings are recordings initiated by the Agent by dialing *# or with a record button at their desk set. If they are logged in as an agent the recording will be placed in this location for easy access by administration or other agents. Typically *# or record will place the recording in a users voicemail in the work folder. However if an Agent is logged in these recording get placed here for easier access by Administration of ACD groups.

Remote Agent Login

With this feature a user can call into the PBX and log a phone number in as an Agent. This will cause any Ring Groups that include that Agent to ring the phone number entered. If the call is answered at this ringing phone number, the user will be prompted to press 1 to accept the call.

Logging the Agent In

To accomplish this, we have added a new Services Destination called Remote Agent Login. You can point a Truck DID direct to this destination, or you can have a Menu option set to this. When a user gets to the Remote Agent Login, they will be prompted to enter their Agent number, password, and the phone number to be called. Once entered, the system will announce the number and ask for a confirmation. After that, Ring Groups that would call the Agent will also ring that phone number.

Logging the Agent Out

To log the Agent out of that phone number, call back into the Remote Agent Login, enter your Agent number and password as prompted, and when the system asks for a phone number, simply press #. Queue Recordings

Edit Automatic Call Distribution (ACD) Agent

STEPS:

  1. From the Destinations Groups Edit Group page, scroll to the ACD Settings section.
  2. Click on the blue Agents link to the right of the words ACD Settings. The Agents page appears.
  3. Update the necessary information for agent(s) then click the SAVE CHANGES button. The changes that you made will appear in the updated list.
  4. Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database

Delete Automatic Call Distribution (ACD) Agent

STEPS:

  1. From the Destinations=>Groups=>Edit Group page, scroll to the ACD Settings section.
  2. Click on the blue Agents link to the right of the words ACD Settings. The Agents page appears.
  3. From the list of existing agents, click on the box (placing a checkmark) to the left of the Agent(s) that you want to delete. Click the DELETE SELECTED button.
  4. The agent selected is removed from the list.
  5. Click Savechanges.png button to save the changes.
  6. Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database.

Alerts

Alerts can be set up to allow notifications to be sent out when a certain number is dialed as an outgoing call, such as 911. Alerts allow a large community to be informed about about the outbound dial quickly. These notifications can be sent as an email, text message, and as an audio tone or message over the phone system and paging system. The alerts can be configured to be sent to only certain extensions or to all extensions.

This alert notification can be sent out to cell phones as well as computers. Link to Alerts video training


Sms.png
Email Alert message
Text.png
Mobile Phone SMS Alert message Email Alert Message Text Message on Manager

Create Alerts

Alertdetail.png
Sections/Fields Description
Alert General Settings
Alert Name Enter what the alert will be called
Enable/Disable this Alert Enabling this alert will allow for notifications to be sent when the desired number is dialed. Disabling this alert will not allow for this function. If you would like notifications to be sent out when a certain outbound number is dialed, be sure to have this feature enabled.
Enable/Disable Text Notifications for this Alert Enabling text notifications will allow chosen recipients to be alerted via their QManager text messages. Disabling this feature will not allow QManager notifications.
Enable/Disable Email Notifications for this Alert Enabling email notifications will allow emails to be sent out to chosen recipients when the alert is set off.

This feature can also send alerts to cell phones as a text message if the recipient has a free gateway service through their cell phone provider such as “@vtext.com” that Verizon provides. (How to send SMS Messages [[1]])

Disabling this feature will not send alerts to email or cell phones.

Enable/Disable Scheduled Call Notifications for this Alert Enabling Scheduled Call notifications sends out an alert tone of your choice to the desired phone extensions. This feature does not require the recipient to be near their computer or phone to receive the alert notification.

Disabling this alert will not allow the tone to be sent out to desired extensions.

Next Destination to Route Caller (non-outbound) When using alerts as a destination, callers who have dialed a specific DID that is routed to the alert or pressed a single digit in a menu that is routed to an alert can combine sending a call and announcing the call with email, text, or external audio messaging.

An example of applying this feature would be in a retail store. If an employee dials for a certain department, there can be notifications sent out via email, text, or audio notifications through out the store alerting the next available employee in the desired department.

Alert Text to be Displayed with this Notification
Email Subject Text Enter the desired alert text that will be sent out via email or text message as the subject heading
Email/Text Message Body Enter what will be sent out in the alert message to email addresses or text alerts.

%DNID: the number that has been dialed out %CALLERID: the extension ID that has dialed the number %TIME: the date and time the number was dialed

Client Text Alerts
Extensions All of the extensions that are part of your system are displayed here. Highlight the ones that you would like to send text alerts to over the QManager application and click add.
QManager Recipients The extensions that you see here are the extensions that will receive text alerts over the QManager application.
Email Alerts
Email Address Enter the email address that you would like to receive email alerts for this notification and click add.
Email Recipients The addresses you see here are the recipients of the email notifications for this alert.
Scheduled Call Alerts
Scheduled Calls The extensions that you see here are the extensions that will receive text alerts through an audio notification over their phone.
Applied to Alert The extensions that you see here are the extensions that will receive text alerts through an audio notification over their phone.


To create an alert:

  1. Navigate to the Alerts page under the Destinations tab.
  2. Click on Create New Alert.
  3. Enter the Alert Name.
  4. Enable the the Alert and any notification system you would like to use.
  5. Add any extensions you would like to be notified when this Alert is set off for text alerts in the QManager, email, and scheduled call alerts.
  6. Click on Savechanges.png.

Edit Alerts

This will allow you to enter the outgoing number that will set off the alerts as well as the notification message you wish to go out with this alert. 

Editoutgoingroute.png
Sections/Fields Description
Edit Outbound Route
Route Name The name of the outbound route for the alert
Route Type The type of outbound route that the alert is. For example, if the alert is for 911, then it would be an emergency outbound route.
Start Pattern This field allows you to enter the patter of digits that would first be entered to set off the alert system.
Digits This field allows you to enter the length of the number that would be dialed for the alert.
Exact Length This gives you a drop down menu that includes yes or no options. The number that is entered can be exactly number of digits that has been specified in the previous field or not.
Trunks See Outgoing Call Routing [[2]]
Assign Alert Notification This drop down menu will give you options for the alert notifications you have created when creating an alert. select the notification that is appropriate for the alert.
  1. Under the Call Routing Tab, navigate to the Outgoing page.
  2. Click on the Outbound Route that you would like to edit.
  3. Select an alert notification for this outbound route.
  4. Click on Savechanges.png.

Multicast Paging Group

A Multicast Paging Group provides a way to page a large number of phones, while keeping the burden on the network and PBX to a minimum.

NOTE: IPitomy recommends using multicast paging for groups of 10 or more phones that are paged frequently.

Multicastgroups.png
Editmultipagewindow.png


The following table describes the fields (parameters) on the Multicast Edit Paging Group window and the recommended settings.

WARNING: Multicast paging DOES NOT WORK from a cloud pbx. In order to simulate multicast paging from cloud, additional specialized hardware will be required, and is not supported directly by IPitomy.


Sections/Fields
Description
Name This is a name of the multicast paging group.
Local Number This is the number that will be dialed to launch the multicast paging to the defined group. This is the unique 3-4 digit number.
Multicast Address This should be a valid multicast IP for a Multicast Address<ref name="ftn1">224.0.0.0 to 239.255.255.255, with many addresses reserved.</ref>. We recommend 225.5.5.5. You can use the same IP for each group, so long as you assign them different ports.
Multicast Port This must be a valid, unused port Multicast Port.

NOTE: This must be a port below 6535.

Time to Live Time to Live is a counter that decreases by 1 each time a packet passes through a router. When the counter reaches 0, the packet is considered dead and will not pass to any other networks. This can be left blank or configured as needed for your particular install.

NOTE: Leaving it blank the packet will not pass to another network.

Members The Members section allows you to add the extensions to be paged within the group when a page is sent.
Add/Remove The Add and Remove button allows you to add or remove members (extensions) from the paging group.
Create/Update Depending on the process that is being performed, this button will appear (be labeled) as either Create or Update. This will create a new member or process the changes made.
Close Window This link will close the Edit Page Group window and return you to the Ring Groups page.

The following section outlines the steps to add a new Multicast Paging Group.

Add Multicast Paging Group

STEPS:

  1. Navigate to the Destinations=>Group page
  2. Locate to the Multicast Paging Groups section (at the bottom of the page).
  3. Click on the Add Groups button. The Edit Page Group page appears.
  4. Enter the necessary information for the new paging group.
  5. From the Members section of the Edit Page Group window, select the members (extensions) that you want to include in the paging group.

Use the CTRL or SHIFT button to select multiple or a range of extensions from the list.

  1. Click on the ADD button to add the selected members to the group.
  2. Click the CREATE button to save the changes. The “Group Created” message appears. Close the window (click on the “X”). The system returns you to the Ring Groups page.
  3. Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database
  4. Re-boot the phones that correspond to extensions that were added to the Multicast Paging Group. Once all the phones have been re-booted, you will be able to utilize this feature by simply dialing the Local Number that was just created.

Edit Multicast Paging Group

STEPS:

  1. Navigate to the Destinations=>Group page
  2. Locate the Multicast Paging Groups section (at the bottom of the page).
  3. Click on Penciledit.png icon to the right of the Name of the paging group you want to update. The Edit Page Group page appears.
  4. Enter the necessary information for the paging group.
  5. Click the UPDATE button to save the changes. Close the window (click on the “X”). The system returns you to the Ring Groups page.
  6. Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database
  7. Re-boot the phones for all the extensions that were involved in the Multicast Paging Group.

Delete Multicast Paging Group

STEPS:

  1. Navigate to the Destinations=>Group page
  2. Locate the Multicast Paging Groups section (at the bottom of the page).
  3. Click on Deleteselected.png icon to the right of the Name of the paging group you want to delete. The group is removed from the Multicast Paging Group page.
  4. Click the Apply Changes link located at the top right hand corner of the page, to commit the changes to the database
  5. Re-boot the phones for all the extensions that were involved in the Multicast Paging Group which was deleted.

Live Queue Data

The Live Queue Data page displays current call statistics for ACD queues. The page will refresh every 10 seconds, allowing a manager to monitor the activity in the queue as it happens. You can Apply Changes if you would like to reset the data.

Ringlivequedata.png
Sections/Fields
Description
<queue selection box> In the queue selection box the Queue or Queues to be displayed can be selected. Use the Control key (Command on Mac) to select multiple queues for display.
<queue statistics box> The Queue Statistics box has been reformatted in SW release 3.4.1 to allow its use on call center wall boards (large PC displays).

Each queue is encapsulated with a thin-line box. Queue statistics are color-coded for quick orientation on wall boards. Since this data is presented in GUI format it can be easily resized to accommodate large displays.

The top line of the queue display presents the Queue Name and the date.

Statistics are a running total and will reset to zero whenever Apply Changes is clicked (as is the case of the screen capture above).

Time in Q This is the average time that callers have waited in queue before being answered by a queue member/agent.
Calls in Q This is the number of calls that are waiting in the queue.
Answered This is the number of calls answered by members/agent of this queue.
Abandoned This is the number of calls that have not been answered and the caller abandoned the queue.
Target Time Displays the service level set for this ACD queue. The Service Level is the arbitrary time allocated by the queue administrator which is set as a gauge by which all calls should be answered.
 % in Target This is the percentage of answered calls measured against the service level. (The percentage of calls being answered within the set Target Time.)
<Member/Agent field> At the right side of the Queue Statistics box the agents and queue members are listed. There are two maximum columns and the window will resize to accommodate all members and agents registered to this queue.

Member/Agent status is available at a glance with color-codes as follows:


Red
=
In Use
Green
=
Idle (Logged In)
Yellow
=
Ringing
Gray
=
Unavailable (Not Logged In)
Orange
=
Paused

Also in the Member/Agent data are two numeral fields. The first number represents the Priority of this Member/Agent in this queue. The second number is the total calls taken by this Member/Agent.

Live Queue Data Wallboard

Software version 3.4.1 and above allows the use of call center wall boards with Live Call Queue. This function is facilitated using a special user name and password via Smart Personal Console.

Activate Live Call Queue Wallboard

STEPS:

  1. Navigate to the PBX Setup=>General page
  2. Locate to the General Settings section (second section from the top).
  3. Locate the SPC Reports User Password field (bottom of section)

Spcreportsuserpass.png<p/>

  1. It may be helpful to change this to a user-friendly password. If you change the password be sure to Savechanges.png and Apply Changes.
  2. Make a note of this password.
  3. On the PC that will be used for the wallboard display, open a web browser and navigate to the IPitomy PBX login screen
  4. Using the right sideSmart Personal Console (User Login) input the word “reports” as the user name and the password saved in step 3. Reportslogin.png
  5. Click on Login .
  6. The CDR-Report page is opened. On this page is a button to select Live Queue.
  7. Click on Live Queue.
  8. The same display presented in PBX Administration is displayed. Simply select the group or groups that you wish to display on the wallboard.
  9. Size this web page data output for the monitor in use by pressing and holding the Cntrl key (PC, Command key on Mac) and press “+” or “-“ until the data is sized as you wish.



<references/>