Difference between revisions of "QOS Setup Guide"

From IPitomy Wiki
Jump to navigation Jump to search
(Created page with "===QOS Setup Guide=== QOS will enhance the function of Voice on the network in EVERY case. There are cases where the use of managed switches will likely not impact the perform...")
 
Line 15: Line 15:
 
For reference only the QOS setting in the PBX is shown:
 
For reference only the QOS setting in the PBX is shown:
  
Step 1. Navigate
+
[[file:PBX GUI - SIP Advanced.gif]]
 +
 
 +
Notice the SIP TOS and RTP TOS are set to "CS3"... this is a reference to make QOS programming easier.
 +
 
 +
The type of service (TOS) field in the IPv4 header has had various purposes over the years, and has been defined in different ways by five RFCs[1]. The modern redefinition of the TOS field is a six-bit Differentiated Services Field (DS field)[2] field and a two-bit Explicit Congestion Notification (ECN) field.[3] While Differentiated Services is somewhat backwards compatible with TOS, ECN is not. (Source: Wikipedia http://en.wikipedia.org/wiki/Type_of_Service)
 +
 
 +
Step 1. Navigate to the switch (we recommend setting the switch or switches to Static IP Address assignments since these are infrastructure devices that must be maintained and often require remote access. (The setting of Static IP Addressing for the switch is not covered in this guide but is very easily done under the heading of System - Management - IP Configuration.)
 +
 
 +
[[file:Netgear_Loging_Screen.gif]]
 +
 
 +
Step 2. Input the password ("password' at default)
 +
 
 +
Step 3. Navigate to the QOS tab
 +
 
 +
Step 4. Navigate to CoS Global Configuration
 +
 
 +
Step 5. Enable QoS
 +
 
 +
Step 6. Set the trust mode to DSCP (Differentiated Services Code Point)
 +
 
 +
[[file:Netgear_QOS_Screen.gif]]
 +
 
 +
Step 7. Navigate to
 +
 
 +
[[file:Netgear_DSCP_to_Queue_Mapping.gif]]

Revision as of 19:48, 6 August 2012

QOS Setup Guide

QOS will enhance the function of Voice on the network in EVERY case. There are cases where the use of managed switches will likely not impact the performance of voice over the network but these exceptions and IPitomy recommends using a Managed Switch on all implementations of voice products.

That said, the implementation of QOS varies greatly from one switch manufacturer to another and therefore we have decided to post this guide for units which we have direct experience.

The Netgear FS728TP product specs are available here: http://www.netgear.com/business/products/switches/smart-switches/FS728TP.aspx

We like the switch because it is cost-effective and efficiently performs the tasks required to optimize a network for voice traffic.

For best performance, ports on a switch should be designated for either non-voice data (PC's, printers, etc.) or voice-data. This isn't always possible but since QOS can be set as part of the packet header, its efficiency can still be realized.

In the FS728TP QOS is set as follows:

For reference only the QOS setting in the PBX is shown:

PBX GUI - SIP Advanced.gif

Notice the SIP TOS and RTP TOS are set to "CS3"... this is a reference to make QOS programming easier.

The type of service (TOS) field in the IPv4 header has had various purposes over the years, and has been defined in different ways by five RFCs[1]. The modern redefinition of the TOS field is a six-bit Differentiated Services Field (DS field)[2] field and a two-bit Explicit Congestion Notification (ECN) field.[3] While Differentiated Services is somewhat backwards compatible with TOS, ECN is not. (Source: Wikipedia http://en.wikipedia.org/wiki/Type_of_Service)

Step 1. Navigate to the switch (we recommend setting the switch or switches to Static IP Address assignments since these are infrastructure devices that must be maintained and often require remote access. (The setting of Static IP Addressing for the switch is not covered in this guide but is very easily done under the heading of System - Management - IP Configuration.)

Netgear Loging Screen.gif

Step 2. Input the password ("password' at default)

Step 3. Navigate to the QOS tab

Step 4. Navigate to CoS Global Configuration

Step 5. Enable QoS

Step 6. Set the trust mode to DSCP (Differentiated Services Code Point)

Netgear QOS Screen.gif

Step 7. Navigate to

Netgear DSCP to Queue Mapping.gif