Difference between revisions of "Yealink"

From IPitomy Wiki
Jump to navigation Jump to search
Line 8: Line 8:
 
*Navigate to Settings=>Auto Provision
 
*Navigate to Settings=>Auto Provision
 
*If the phone is local: Set Server URL to <pre>TFTP://&lt;IP address of pbx&gt;/</pre>
 
*If the phone is local: Set Server URL to <pre>TFTP://&lt;IP address of pbx&gt;/</pre>
*If the phone is remote: Set server URL to <pre>http://1234@admin/<public IP address of pbx>/ippbx/phonecfg/</pre>
+
*If the phone is remote: Set server URL to <pre>http://<public IP address of pbx>/ippbx/phonecfg/</pre>
 +
*If the phone is remote: Set the username to admin, and the password to 1234
 
*Click Confirm at the bottom of the page
 
*Click Confirm at the bottom of the page
 
*Click Auto Provision Now
 
*Click Auto Provision Now

Revision as of 13:38, 12 July 2017

Beginning in PBX software version 5.2.1-10, we have begun including more integrated support for Yealink phones. They can now be found via autodiscovery and assigned to extensions, although they do not currently respond to configure or restart commands. Yealink phones CAN autoprovision from the pbx once assigned, however, by either logging into each phone's webGUI, or using our quick setup utility. The quick setup utility can be downloaded here Yealink Quick Setup utility


Auto Provisioning a Yealink Phone

  • Log into the GUI interface of phone via its IP Address (user: admin/pass:admin)
  • Navigate to Settings=>Auto Provision
  • If the phone is local: Set Server URL to
    TFTP://<IP address of pbx>/
  • If the phone is remote: Set server URL to
    http://<public IP address of pbx>/ippbx/phonecfg/
  • If the phone is remote: Set the username to admin, and the password to 1234
  • Click Confirm at the bottom of the page
  • Click Auto Provision Now

The phone's screen should change to indicate that it is updating its config, and will then register if successful.

Quick Setup Guide

Use this in conjunction with the quick setup utility

Additional programming tips:

Keys

  • When configuring the Park key manually, set the type to DTMF, and the value to ##700#.
  • When configuring a Record key manually, set the type to DTMF, and the value to *#
  • When configuring the Day/Night key manually, set the type to BLF and the value to ff.
  • Under the DDS key tab is a link for Line Keys. Be sure to set the Line Keys to Account 1 if you want them to function as a line key, otherwise you can configure them just like any other programmable key.


Multicast

To set up multicast on your Yealink phone:

  • Log into the GUI interface of phone via its IP Address (user: admin/pass:admin)
  • Navigate to Contacts=>MulticastIP
  • Populate the Listening Address field with the mutlicast IP of the multicast group built in the PBX, followed by a colon and the port configured for the group.
    • eg. 225.5.5.5:1235
  • Populate the Label field with a name that will display on the LCD when paged by the multicast group
  • Click the Confirm key and your settings will be saved, allowing the phone to receive multicast pages.

A dealer has brought to our attention this link to a Yealink forum that has a firmware for multicast. I know in our testing, the .143 version had the settings needed. But its possible you may need this version as that is what the dealer needed, so we are linking to the information.

http://forum.yealink.com/forum/showthread.php?tid=189&page=3

Fixes

  • T38G firmware version fixes an issue with Parked calls bonding with other calls incorrectly.  Extract the .rom from the Zip folder and load it into the phone.

File:38.70.0.143.zip