IP PBX Manual System Networking - Revision history

Mike Lunn: /* Load Recommended Default */

2022-04-22T13:08:26Z

Load Recommended Default

← Older revision		Revision as of 13:08, 22 April 2022
Line 157:		Line 157:
	#Navigate to the '''Access Control List''' page, click '''Load Recommended Default''' button. This will create default rules allowing the PBX to communicate to devices on the LocalNet in regards to SIP, Call Manager, and TFTP		#Navigate to the '''Access Control List''' page, click '''Load Recommended Default''' button. This will create default rules allowing the PBX to communicate to devices on the LocalNet in regards to SIP, Call Manager, and TFTP
	#Click the '''Apply Changes''' link located on the right hand corner of the page, to commit the changes to the database.		#Click the '''Apply Changes''' link located on the right hand corner of the page, to commit the changes to the database.
			[[File:Load defaults.png\|none\|frame]]

	=== Add New Service ===		=== Add New Service ===

Mike Lunn: /* Users */

2017-11-29T20:13:22Z

Users

← Older revision		Revision as of 20:13, 29 November 2017
Line 277:		Line 277:
	=== Users ===		=== Users ===

	Once a Group is created, you can add Users. To do so, you'll need to give them a Username and Password, enter the Name to know which person this User was created for, and set them to a Group. Once created, if you need to modify a field for a User, simply populate the Username field and whichever fields you wish to change, then click Save.		Once a Group is created, you can add Users. To do so, you'll need to give them a Username and Password, enter the Name to know which person this User was created for, and set them to a Group. Once created, if you need to modify a field for a User, simply populate the Username field and whichever fields you wish to change, then click Save. The username must be a minimum of 4 characters, or it will create the entry, and then give a bad username or password error when you attempt to log in.

	[[File:AdminUsers.jpg\|File:AdminUsers.jpg]]		[[File:AdminUsers.jpg\|File:AdminUsers.jpg]]

Mike Lunn: /* VLAN */

2017-11-16T22:24:45Z

VLAN

← Older revision		Revision as of 22:24, 16 November 2017
Line 53:		Line 53:

	== VLAN ==		== VLAN ==
	~~edit~~		{{:VLAN}}

	== Access Control (PBX Access)<br/> ==		== Access Control (PBX Access)<br/> ==

Mike Lunn at 21:54, 16 November 2017

2017-11-16T21:54:01Z

← Older revision		Revision as of 21:54, 16 November 2017
Line 51:		Line 51:
	#Click on the '''Save Changes''' button		#Click on the '''Save Changes''' button
	#Click the '''Apply Changes''' link located on the right hand corner of the page, to commit the changes to the database.		#Click the '''Apply Changes''' link located on the right hand corner of the page, to commit the changes to the database.

			== VLAN ==
			edit

	== Access Control (PBX Access)<br/> ==		== Access Control (PBX Access)<br/> ==

Mike Lunn: /* Groups */

2016-02-29T22:42:34Z

Groups

← Older revision		Revision as of 22:42, 29 February 2016
Line 268:		Line 268:
	[[File:AdminGroups.jpg\|File:AdminGroups.jpg]]		[[File:AdminGroups.jpg\|File:AdminGroups.jpg]]

	Once created you will need to Edit and choose what features on the PBX the user is able to control. For each feature, you can choose Create, Modify, Delete, as well as filter. Separate multiple filters of the same feature with commas.		Once created you will need to Edit and choose what features on the PBX the user is able to control. For each feature, you can choose Create, Modify, Delete, as well as filter. Separate multiple filters of the same feature with commas. Filters can be used on Extensions, Groups, Menus, and Conferences.

	[[File:AdminGroupsEdit.jpg\|File:AdminGroupsEdit.jpg]]		[[File:AdminGroupsEdit.jpg\|File:AdminGroupsEdit.jpg]]

Mike Lunn: /* UI Users & Groups */

2015-12-01T18:25:53Z

UI Users & Groups

← Older revision		Revision as of 18:25, 1 December 2015
Line 258:		Line 258:
	To add an IP to the list, enter <ipaddress>/<subnetmask> in the text field and click add.  Highlight an entry and click Delete to remove it from the list.  As always, you must Save first, then Apply Changes for these features to become active on the live system.		To add an IP to the list, enter <ipaddress>/<subnetmask> in the text field and click add.  Highlight an entry and click Delete to remove it from the list.  As always, you must Save first, then Apply Changes for these features to become active on the live system.

	== UI Users & Groups ==		== UI Users & Admin Groups ==

	With Users and Groups, you the admin can give a user access to the programming side of the PBX and customize what they are able to modify, create, or delete.		With Users and Groups, you the admin can give a user access to the programming side of the PBX and customize what they are able to modify, create, or delete.

Mike Lunn: /* System */

2015-12-01T17:33:43Z

System

← Older revision		Revision as of 17:33, 1 December 2015
Line 1:		Line 1:
	__NOTITLE__		__NOTITLE__
	{{IP_PBX_Manual\|sortkey=System Networking}}		{{IP_PBX_Manual\|sortkey=System Networking}}
	= '''System'''<br/> =		== '''System Networking'''<br/> ==

	The IPitomy System Menu is for configuring network attributes. For example the IP address of the system and router information. The System Networking Setup Page allows you to define the Internet Setup for the system’s hardware. The system must operate using a static IP address; DHCP should only be used on the IPitomy IP PBX if the router is configured to assign a specific static DHCP address to the system. [[File:Tcpipsettings.png\|center\|Tcpipsettings.png]]<br/>The following table describes the fields and recommended settings for Networking Setup for the IP PBX system:		The IPitomy System Menu is for configuring network attributes. For example the IP address of the system and router information. The System Networking Setup Page allows you to define the Internet Setup for the system’s hardware. The system must operate using a static IP address; DHCP should only be used on the IPitomy IP PBX if the router is configured to assign a specific static DHCP address to the system. [[File:Tcpipsettings.png\|center\|Tcpipsettings.png]]<br/>The following table describes the fields and recommended settings for Networking Setup for the IP PBX system:

Mike Lunn at 17:33, 1 December 2015

2015-12-01T17:33:06Z

← Older revision		Revision as of 17:33, 1 December 2015
Line 1:		Line 1:
	__NOTITLE__		__NOTITLE__
	{{IP_PBX_Manual\|sortkey=System Networking}}		{{IP_PBX_Manual\|sortkey=System Networking}}
	= '''System ~~Networking~~'''<br/> =		= '''System'''<br/> =

	The IPitomy System Menu is for configuring network attributes. For example the IP address of the system and router information. The System Networking Setup Page allows you to define the Internet Setup for the system’s hardware. The system must operate using a static IP address; DHCP should only be used on the IPitomy IP PBX if the router is configured to assign a specific static DHCP address to the system. [[File:Tcpipsettings.png\|center\|Tcpipsettings.png]]<br/>The following table describes the fields and recommended settings for Networking Setup for the IP PBX system:		The IPitomy System Menu is for configuring network attributes. For example the IP address of the system and router information. The System Networking Setup Page allows you to define the Internet Setup for the system’s hardware. The system must operate using a static IP address; DHCP should only be used on the IPitomy IP PBX if the router is configured to assign a specific static DHCP address to the system. [[File:Tcpipsettings.png\|center\|Tcpipsettings.png]]<br/>The following table describes the fields and recommended settings for Networking Setup for the IP PBX system:

Mike Lunn: /* UI Users & Groups */

2015-11-09T16:32:20Z

UI Users & Groups

← Older revision		Revision as of 16:32, 9 November 2015
Line 259:		Line 259:

	== UI Users & Groups ==		== UI Users & Groups ==

	With Users and Groups, you the admin can give a user access to the programming side of the PBX and customize what they are able to modify, create, or delete.		With Users and Groups, you the admin can give a user access to the programming side of the PBX and customize what they are able to modify, create, or delete.

	===Groups===		=== Groups ===
	Start by adding a Group that will define what features the user is able to edit. You need to set a Group ID (number) and Group Name.
			Start by adding a Group that will define what features the user is able to edit. You need to set a Group ID (number) and Group Name.

			[[File:AdminGroups.jpg\|File:AdminGroups.jpg]]

			Once created you will need to Edit and choose what features on the PBX the user is able to control. For each feature, you can choose Create, Modify, Delete, as well as filter. Separate multiple filters of the same feature with commas.

			[[File:AdminGroupsEdit.jpg\|File:AdminGroupsEdit.jpg]]

			=== Users ===

	Once created you ~~will~~ need to ~~Edit~~ and ~~choose what features on~~ the ~~PBX the user is able~~ to ~~control~~. ~~For each feature~~, you ~~can choose Create~~, ~~Modify, Delete~~, ~~as well as filter. Separate multiple filters of the same feature with commas~~.		Once a Group is created, you can add Users. To do so, you'll need to give them a Username and Password, enter the Name to know which person this User was created for, and set them to a Group. Once created, if you need to modify a field for a User, simply populate the Username field and whichever fields you wish to change, then click Save.

	~~===Users===~~		[[File:AdminUsers.jpg\|File:AdminUsers.jpg]]
	~~Once a Group is created, you can add Users~~. To do so, you'll need to give them a Username and Password, enter the Name to know which person this User was created for, and set them to a Group. Once created, if you need to modify a field for a User, simply populate the Username field and whichever fields you wish to change, then click Save.

Mike Lunn at 16:30, 9 November 2015

2015-11-09T16:30:15Z

← Older revision		Revision as of 16:30, 9 November 2015
Line 257:		Line 257:

	To add an IP to the list, enter <ipaddress>/<subnetmask> in the text field and click add.  Highlight an entry and click Delete to remove it from the list.  As always, you must Save first, then Apply Changes for these features to become active on the live system.		To add an IP to the list, enter <ipaddress>/<subnetmask> in the text field and click add.  Highlight an entry and click Delete to remove it from the list.  As always, you must Save first, then Apply Changes for these features to become active on the live system.

			== UI Users & Groups ==
			With Users and Groups, you the admin can give a user access to the programming side of the PBX and customize what they are able to modify, create, or delete.

			===Groups===
			Start by adding a Group that will define what features the user is able to edit. You need to set a Group ID (number) and Group Name.

			Once created you will need to Edit and choose what features on the PBX the user is able to control. For each feature, you can choose Create, Modify, Delete, as well as filter. Separate multiple filters of the same feature with commas.

			===Users===
			Once a Group is created, you can add Users. To do so, you'll need to give them a Username and Password, enter the Name to know which person this User was created for, and set them to a Group. Once created, if you need to modify a field for a User, simply populate the Username field and whichever fields you wish to change, then click Save.