Multitech Fax Finder - Revision history

Mike Lunn at 18:07, 23 May 2019

2019-05-23T18:07:52Z

← Older revision		Revision as of 18:07, 23 May 2019
Line 47:		Line 47:
	[[File:Multitech sip 4.jpg\|File:Multitech sip 4.jpg]]		[[File:Multitech sip 4.jpg\|File:Multitech sip 4.jpg]]

	3) In the PBX Make sure that you have Fax Detect Set to yes on your PRI or Analog Card. Note: ~~FAX DETECT DOES NOT WORK OVER~~ SIP~~. It is for use with analog lines or PRI only~~.		3) In the PBX Make sure that you have Fax Detect Set to yes on your PRI or Analog Card. Note: Fax detect does not work on inbound calls from a SIP trunk.

Mike Lunn at 18:02, 23 May 2019

2019-05-23T18:02:18Z

← Older revision		Revision as of 18:02, 23 May 2019
Line 47:		Line 47:
	[[File:Multitech sip 4.jpg\|File:Multitech sip 4.jpg]]		[[File:Multitech sip 4.jpg\|File:Multitech sip 4.jpg]]

	3) In the PBX Make sure that you have Fax Detect Set to yes on your PRI or Analog Card. Note: FAX DETECT DOES NOT WORK OVER SIP.		3) In the PBX Make sure that you have Fax Detect Set to yes on your PRI or Analog Card. Note: FAX DETECT DOES NOT WORK OVER SIP. It is for use with analog lines or PRI only.

Mike Lunn at 18:01, 23 May 2019

2019-05-23T18:01:06Z

← Older revision		Revision as of 18:01, 23 May 2019
Line 47:		Line 47:
	[[File:Multitech sip 4.jpg\|File:Multitech sip 4.jpg]]		[[File:Multitech sip 4.jpg\|File:Multitech sip 4.jpg]]

	3) In the PBX Make sure that you have Fax Detect Set to yes on your PRI or Analog Card.		3) In the PBX Make sure that you have Fax Detect Set to yes on your PRI or Analog Card. Note: FAX DETECT DOES NOT WORK OVER SIP.

John Wolfe at 15:07, 11 March 2014

2014-03-11T15:07:27Z

← Older revision		Revision as of 15:07, 11 March 2014
Line 55:		Line 55:
	Once this is configured, you can set a DID to a Fax extension. And test Inbound to this extension. The Multitech SIP Fax Finder IP will receive the Fax and email to the respective email address. For outbound you will need to install the Fax Finder client software. This is were you will need to configure the User and Password for outbound use. Once installed this is used as a Printer on your PC. And you simply print to the Fax Driver. It will send using the credentials provided.		Once this is configured, you can set a DID to a Fax extension. And test Inbound to this extension. The Multitech SIP Fax Finder IP will receive the Fax and email to the respective email address. For outbound you will need to install the Fax Finder client software. This is were you will need to configure the User and Password for outbound use. Once installed this is used as a Printer on your PC. And you simply print to the Fax Driver. It will send using the credentials provided.

	==Multitech SIP Fax Finder For PBX Software Versions prior to Version 5.0X==		== Multitech SIP Fax Finder IP For PBX Software Versions prior to Version 5.0X ==

	NOTE: This instruction set should be used only for systems which are prior to 5.0X		NOTE: This instruction set should be used only for systems which are prior to 5.0X

	The Multitech SIP Fax Finder will register to the PBX as a SIP provider. Once configured, calls will be sent to the Fax Finder via an Outbound Dialing Route. The digits dialed outbound will be read by the Fax Finder to define the recipient of the fax.		The Multitech SIP Fax Finder IP will register to the PBX as a SIP provider. Once configured, calls will be sent to the Fax Finder via an Outbound Dialing Route. The digits dialed outbound will be read by the Fax Finder to define the recipient of the fax.

	*Configure a SIP provider in the PBX to register to the Fax Finder		*Configure a SIP provider in the PBX to register to the Fax Finder

John Wolfe: /* Multitech SIP Fax Finder IP For PBX Software Versions 5.0X and Higher */

2014-03-11T15:05:50Z

Multitech SIP Fax Finder IP For PBX Software Versions 5.0X and Higher

@@ Line 9: / Line 9: @@
 **The DP Digits should correspond to the User that was created in the Fax Finder.  This way, when the Fax Finder answers, the PBX plays the digits into the line and the Fax Finder can email the fax to the correct recipient.
-==Multitech SIP Fax Finder IP For PBX Software Versions 5.0X and Higher==
+== Multitech SIP Fax Finder IP For PBX Software Versions 5.0X and Higher ==
 NOTE: You must be on Version 5.0X and higher for this instruction set to work.
 The Multitech SIP Fax Finder IP will register as an Extension to the PBX. Each Fax user will need to also have an additional Fax extension created in the PBX.
 ) Create an Extension in the PBX for the Fax Finder. This Extension should have the Host field set as the IP of the FAX Finder. Also there should be nothing in the Qualify field. And additionally there is no SIP password so you must blank this field. And these Extensions should all be set to Is Fax Extension - yes. You may have as many Fax Extensions as you have Open licenses to accommodate.
-) In the Multitech SIP Fax Finder IP navigate to Fax Configuration - SIP T.38 And set the SIP Proxy /Gateway to the IP of the PBX. Under Inbound Routing, set up a Recipient account for each FAX extension created. All that is needed in the recipient information is the Name and Extension Number and to define a User. To define the user you must create a Fax User account, under Users - Multitech SIP Fax Finder IP Users. Configure each user with a Name, Password, Email Address and Phone number. This information is primarily used for outbound.
+[[File:Multitech sip 5.jpg|File:Multitech sip 5.jpg]]
-) In the PBX Make sure that you have Fax Detect Set to yes on your PRI or Analog Card.
+) In the Multitech SIP Fax Finder IP navigate to Fax Configuration - SIP T.38 And set the SIP Proxy /Gateway to the IP of the PBX.
 Once this is configured, you can set a DID to a Fax extension. And test Inbound to this extension. The Multitech SIP Fax Finder IP will receive the Fax and email to the respective email address. For outbound you will need to install the Fax Finder client software. This is were you will need to configure the User and Password for outbound use. Once installed this is used as a Printer on your PC. And you simply print to the Fax Driver. It will send using the credentials provided.

John Wolfe: /* Multitech SIP Fax Finder IP For PBX Software Versions 5.0X and Higher */

2014-03-11T13:38:30Z

Multitech SIP Fax Finder IP For PBX Software Versions 5.0X and Higher

← Older revision		Revision as of 13:38, 11 March 2014
Line 13:		Line 13:
	NOTE: You must be on Version 5.0X and higher for this instruction set to work.		NOTE: You must be on Version 5.0X and higher for this instruction set to work.

	The Multitech Fax ~~finder~~ will register as an Extension to the PBX. Each Fax user will need to also have an additional Fax extension created in the PBX.		The Multitech SIP Fax Finder IP will register as an Extension to the PBX. Each Fax user will need to also have an additional Fax extension created in the PBX.

	1) Create an Extension in the PBX for the Fax Finder. This Extension should have the Host field set as the IP of the FAX Finder. Also there should be nothing in the Qualify field. And additionally there is no SIP password so you must blank this field. And these Extensions should all be set to Is Fax Extension - yes. You may have as many Fax Extensions as you have Open licenses to accommodate.		1) Create an Extension in the PBX for the Fax Finder. This Extension should have the Host field set as the IP of the FAX Finder. Also there should be nothing in the Qualify field. And additionally there is no SIP password so you must blank this field. And these Extensions should all be set to Is Fax Extension - yes. You may have as many Fax Extensions as you have Open licenses to accommodate.

	2) In the Fax Finder navigate to Fax Configuration - SIP T.38 And set the SIP Proxy /Gateway to the IP of the PBX. Under Inbound Routing, set up a Recipient account for each FAX extension created. All that is needed in the recipient information is the Name and Extension Number and to define a User. To define the user you must create a Fax User account, under Users - ~~FaxFinder~~ Users. Configure each user with a Name, Password, Email Address and Phone number. This information is primarily used for outbound.		2) In the Multitech SIP Fax Finder IP navigate to Fax Configuration - SIP T.38 And set the SIP Proxy /Gateway to the IP of the PBX. Under Inbound Routing, set up a Recipient account for each FAX extension created. All that is needed in the recipient information is the Name and Extension Number and to define a User. To define the user you must create a Fax User account, under Users - Multitech SIP Fax Finder IP Users. Configure each user with a Name, Password, Email Address and Phone number. This information is primarily used for outbound.

	3) In the PBX Make sure that you have Fax Detect Set to yes on your PRI or Analog Card.		3) In the PBX Make sure that you have Fax Detect Set to yes on your PRI or Analog Card.

	Once this is configured, you can set a DID to a Fax extension. And test Inbound to this extension. The ~~FaxFinder~~ will receive the Fax and email to the respective email address. For outbound you will need to install the Fax Finder client software. This is were you will need to configure the User and Password for outbound use. Once installed this is used as a Printer on your PC. And you simply print to the Fax Driver. It will send using the credentials provided.		Once this is configured, you can set a DID to a Fax extension. And test Inbound to this extension. The Multitech SIP Fax Finder IP will receive the Fax and email to the respective email address. For outbound you will need to install the Fax Finder client software. This is were you will need to configure the User and Password for outbound use. Once installed this is used as a Printer on your PC. And you simply print to the Fax Driver. It will send using the credentials provided.

	==Multitech SIP Fax Finder For PBX Software Versions prior to Version 5.0X==		==Multitech SIP Fax Finder For PBX Software Versions prior to Version 5.0X==

Drew Harrell: /* Multitech SIP Fax Finder IP For PBX Software Versions 5.0X and Higher */

2014-03-10T21:17:46Z

Multitech SIP Fax Finder IP For PBX Software Versions 5.0X and Higher

← Older revision		Revision as of 21:17, 10 March 2014
Line 21:		Line 21:
	3) In the PBX Make sure that you have Fax Detect Set to yes on your PRI or Analog Card.		3) In the PBX Make sure that you have Fax Detect Set to yes on your PRI or Analog Card.

	Once this is configured, you can set a DID to a Fax extension. And test Inbound to this extension. The FaxFinder will receive the Fax and email to the respective email address. For outbound you will need to install the Fax Finder client software. This is were you will need to configure the User and Password for outbound use. Once installed this is used as a Printer on your PC. And you ~~siply~~ print to the Fax Driver. It will send using the credentials provided.		Once this is configured, you can set a DID to a Fax extension. And test Inbound to this extension. The FaxFinder will receive the Fax and email to the respective email address. For outbound you will need to install the Fax Finder client software. This is were you will need to configure the User and Password for outbound use. Once installed this is used as a Printer on your PC. And you simply print to the Fax Driver. It will send using the credentials provided.

	==Multitech SIP Fax Finder For PBX Software Versions prior to Version 5.0X==		==Multitech SIP Fax Finder For PBX Software Versions prior to Version 5.0X==

Drew Harrell: /* Multitech SIP Fax Finder For PBX Software Versions 5.0X and Higher */

2014-03-10T21:16:21Z

Multitech SIP Fax Finder For PBX Software Versions 5.0X and Higher

← Older revision		Revision as of 21:16, 10 March 2014
Line 9:		Line 9:
	**The DP Digits should correspond to the User that was created in the Fax Finder. This way, when the Fax Finder answers, the PBX plays the digits into the line and the Fax Finder can email the fax to the correct recipient.		**The DP Digits should correspond to the User that was created in the Fax Finder. This way, when the Fax Finder answers, the PBX plays the digits into the line and the Fax Finder can email the fax to the correct recipient.

	==Multitech SIP Fax Finder For PBX Software Versions 5.0X and Higher==		==Multitech SIP Fax Finder IP For PBX Software Versions 5.0X and Higher==

	NOTE: You must be on Version 5.0X and higher for this instruction set to work.		NOTE: You must be on Version 5.0X and higher for this instruction set to work.
Line 21:		Line 21:
	3) In the PBX Make sure that you have Fax Detect Set to yes on your PRI or Analog Card.		3) In the PBX Make sure that you have Fax Detect Set to yes on your PRI or Analog Card.

	Once this is configured, you can set a DID to a Fax extension. And test Inbound to this extension. The FaxFinder will receive the Fax and email to the respective email address. For outbound you will need to install the Fax Finder client software. This is were you will need to configure the User and Password for outbound use. Once installed this is used as a Printer on your PC. And you siply print to the Fax Driver. It will send using the credentials provided.		Once this is configured, you can set a DID to a Fax extension. And test Inbound to this extension. The FaxFinder will receive the Fax and email to the respective email address. For outbound you will need to install the Fax Finder client software. This is were you will need to configure the User and Password for outbound use. Once installed this is used as a Printer on your PC. And you siply print to the Fax Driver. It will send using the credentials provided.



	==Multitech SIP Fax Finder For PBX Software Versions prior to Version 5.0X==		==Multitech SIP Fax Finder For PBX Software Versions prior to Version 5.0X==

John Wolfe: /* Multitech SIP Fax Finder */

2014-03-10T20:19:25Z

Multitech SIP Fax Finder

@@ Line 9: / Line 9: @@
 **The DP Digits should correspond to the User that was created in the Fax Finder.  This way, when the Fax Finder answers, the PBX plays the digits into the line and the Fax Finder can email the fax to the correct recipient.
-==Multitech SIP Fax Finder==
+==Multitech SIP Fax Finder For PBX Software Versions 5.0X and Higher==
 NOTE: This instruction set should be used only for systems which are prior to 5.0X

John Wolfe: /* Multitech Analog Fax Finder */

2014-03-10T18:50:50Z

Multitech Analog Fax Finder

← Older revision		Revision as of 18:50, 10 March 2014
Line 9:		Line 9:
	**The DP Digits should correspond to the User that was created in the Fax Finder. This way, when the Fax Finder answers, the PBX plays the digits into the line and the Fax Finder can email the fax to the correct recipient.		**The DP Digits should correspond to the User that was created in the Fax Finder. This way, when the Fax Finder answers, the PBX plays the digits into the line and the Fax Finder can email the fax to the correct recipient.

	==Multitech SIP Fax Finder== NOTE: This instruction set should be used only for systems which are prior to 5.0X		==Multitech SIP Fax Finder==

			NOTE: This instruction set should be used only for systems which are prior to 5.0X

	The Multitech SIP Fax Finder will register to the PBX as a SIP provider. Once configured, calls will be sent to the Fax Finder via an Outbound Dialing Route. The digits dialed outbound will be read by the Fax Finder to define the recipient of the fax.		The Multitech SIP Fax Finder will register to the PBX as a SIP provider. Once configured, calls will be sent to the Fax Finder via an Outbound Dialing Route. The digits dialed outbound will be read by the Fax Finder to define the recipient of the fax.