USB Recovery Dongle - Revision history

Mike Lunn at 22:04, 9 June 2015

2015-06-09T22:04:36Z

← Older revision		Revision as of 22:04, 9 June 2015
Line 3:		Line 3:
	2) Copy the two (2) files into the same directory.		2) Copy the two (2) files into the same directory.

	3) Insert a formated(FAT32), 1GBSB Drive to your PC~~<br/><br/>~~4) Double click on YUMI-0.0.2.8.exe~~<br/><br/>~~5) If a Security Warning pops up, click [Run]~~<br/><br/>~~6) License agreement<br/>Click [I Agree]~~<br/><br/>~~7) YUMI Setup Dialog<br/>Click the drop down list in the upper left<br/>Select the Drive letter of your USB Drive~~<br/><br/>~~8) In the upper right corner Select Format Drive (Erase Content)~~<br/><br/>~~9) From the list box under Step 2, scroll down to:<br/>System Rescue CD and highlight it.~~<br/><br/>~~10) Click the [Browse] button near the lower right corner<br/>Select the file:<br/>systemrescuecd-x86-2.3.1.iso<br/>and click [Open]~~<br/><br/>~~11) Click the [Create] button at the bottom of the dialog~~<br/><br/>~~12) Click [Yes] to perform listed actions~~<br/><br/>~~13) Wait about four (4) minutes~~<br/><br/>~~14) At the Installation Complete Dialog<br/>Make sure that there are no errors listed in the green text<br/>Click [Next]~~<br/><br/>~~15) At the "Would you like to add more ISOs/Distros Now?" question,<br/>Click [No]~~<br/><br/>~~16) At the dancing penguin dialog, click [Finish]~~<br/><br/>~~17) Eject the USB Drive<br/><br/>18) Insert USB Dongle into the PBX~~<br/><br/>~~19) Power the PBX on<br/><br/>20) Enter the BIOS and ensure the PBX is set to Boot from USB (This may be by pressing the Delete key or F2 or F3 key at the right time, the display will tell you what to do to enter BIOS. It may flash by quickly)<br/><br/>Once booted:<br/><br/>21) At the YUMI MultiBoot USB screen<br/><br/>22) Select System Tools<br/>(press Enter)<br/><br/>23) Select System Rescue CD<br/>(press Enter)<br/><br/>24) Select "#1 Default Boot Options"<br/>(first in the list)<br/>(press Enter)<br/><br/>(messages scroll past)<br/>(patience)<br/><br/>25) If it stops at the "Load Keymap" prompt, just press Enter<br/><br/>If everything goes well, you should be at a command prompt:<br/><br/>root@sysresccd /root %<br/><br/>26) Now you will type commands with a keyboard connected to the PBX:<br/><br/>fsck -y /dev/sda1<br/>(press Enter)<br/>(wait for the prompt to return)<br/><br/>fsck -y /dev/sda2<br/>(press Enter)<br/>(wait for the prompt to return)<br/><br/>fsck -y /dev/sda5<br/>(press Enter)<br/>(wait for the prompt to return)<br/>(NOTE!!! This is the main partition and can take awhile to clean up. Patience is HIGHLY recommended at this point)<br/><br/>Once the prompt returns Shutdown the PBX with this command:<br/><br/>shutdown -h now<br/><br/>After it has shutdown, remove the USB dongle and power up the PBX.<br/>Keep a monitor attached to watch.<br/><br/>If everything has gone correctly, you should be at the login prompt.<br/>Connect to the PBX with the web browser and attempt to login.		3) Insert a formated(FAT32), 1GBSB Drive to your PC

			4) Double click on YUMI-0.0.2.8.exe

			5) If a Security Warning pops up, click [Run]

			6) License agreement<br/>Click [I Agree]

			7) YUMI Setup Dialog<br/>Click the drop down list in the upper left<br/>Select the Drive letter of your USB Drive

			8) In the upper right corner Select Format Drive (Erase Content)

			9) From the list box under Step 2, scroll down to:<br/>System Rescue CD and highlight it.

			10) Click the [Browse] button near the lower right corner<br/>Select the file:<br/>systemrescuecd-x86-2.3.1.iso<br/>and click [Open]

			11) Click the [Create] button at the bottom of the dialog

			12) Click [Yes] to perform listed actions

			13) Wait about four (4) minutes

			14) At the Installation Complete Dialog<br/>Make sure that there are no errors listed in the green text<br/>Click [Next]

			15) At the "Would you like to add more ISOs/Distros Now?" question,<br/>Click [No]

			16) At the dancing penguin dialog, click [Finish]

			17) Eject the USB Drive<br/><br/>18) Insert USB Dongle into the PBX

			19) Power the PBX on<br/><br/>20) Enter the BIOS and ensure the PBX is set to Boot from USB (This may be by pressing the Delete key or F2 or F3 key at the right time, the display will tell you what to do to enter BIOS. It may flash by quickly)<br/><br/>Once booted:<br/><br/>21) At the YUMI MultiBoot USB screen<br/><br/>22) Select System Tools<br/>(press Enter)<br/><br/>23) Select System Rescue CD<br/>(press Enter)<br/><br/>24) Select "#1 Default Boot Options"<br/>(first in the list)<br/>(press Enter)<br/><br/>(messages scroll past)<br/>(patience)<br/><br/>25) If it stops at the "Load Keymap" prompt, just press Enter<br/><br/>If everything goes well, you should be at a command prompt:<br/><br/>root@sysresccd /root %<br/><br/>26) Now you will type commands with a keyboard connected to the PBX:<br/><br/>fsck -y /dev/sda1<br/>(press Enter)<br/>(wait for the prompt to return)<br/><br/>fsck -y /dev/sda2<br/>(press Enter)<br/>(wait for the prompt to return)<br/><br/>fsck -y /dev/sda5<br/>(press Enter)<br/>(wait for the prompt to return)<br/>(NOTE!!! This is the main partition and can take awhile to clean up. Patience is HIGHLY recommended at this point)<br/><br/>Once the prompt returns Shutdown the PBX with this command:<br/><br/>shutdown -h now<br/><br/>After it has shutdown, remove the USB dongle and power up the PBX.<br/>Keep a monitor attached to watch.<br/><br/>If everything has gone correctly, you should be at the login prompt.<br/>Connect to the PBX with the web browser and attempt to login.

Mike Lunn at 22:02, 9 June 2015

2015-06-09T22:02:35Z

← Older revision		Revision as of 22:02, 9 June 2015
Line 1:		Line 1:
	USB Recovery Dongle Instructions:<br/>---------------------------------<br/><br/>1) Go to this website<br/>[http://www.ipitomy.com/webrelease/USB_Disk/rescue_disk/ http://www.ipitomy.com/webrelease/USB_Disk/rescue_disk/]<br/>and download the two files<br/>systemrescuecd-x86-2.3.1.iso<br/>YUMI-0.0.2.8.exe		USB Recovery Dongle Instructions:<br/>---------------------------------<br/><br/>1) Go to this website<br/>[http://www.ipitomy.com/webrelease/USB_Disk/rescue_disk/ http://www.ipitomy.com/webrelease/USB_Disk/rescue_disk/]<br/>and download the two files<br/>systemrescuecd-x86-2.3.1.iso<br/>YUMI-0.0.2.8.exe

	2) Copy the two (2) files into the same directory.		2) Copy the two (2) files into the same directory.

	3) Insert a formated(FAT32), 1GBSB Drive to your PC<br/><br/>4) Double click on YUMI-0.0.2.8.exe<br/><br/>5) If a Security Warning pops up, click [Run]<br/><br/>6) License agreement<br/>Click [I Agree]<br/><br/>7) YUMI Setup Dialog<br/>Click the drop down list in the upper left<br/>Select the Drive letter of your USB Drive<br/><br/>8) In the upper right corner Select Format Drive (Erase Content)<br/><br/>9) From the list box under Step 2, scroll down to:<br/>System Rescue CD and highlight it.<br/><br/>10) Click the [Browse] button near the lower right corner<br/>Select the file:<br/>systemrescuecd-x86-2.3.1.iso<br/>and click [Open]<br/><br/>11) Click the [Create] button at the bottom of the dialog<br/><br/>12) Click [Yes] to perform listed actions<br/><br/>13) Wait about four (4) minutes<br/><br/>14) At the Installation Complete Dialog<br/>Make sure that there are no errors listed in the green text<br/>Click [Next]<br/><br/>15) At the "Would you like to add more ISOs/Distros Now?" question,<br/>Click [No]<br/><br/>16) At the dancing penguin dialog, click [Finish]<br/><br/>17) Eject the USB Drive<br/><br/>18) Insert USB Dongle into the PBX<br/><br/>19) Power the PBX on<br/><br/>20) Enter the BIOS and ensure the PBX is set to Boot from USB (This may be by pressing the Delete key or F2 or F3 key at the right time, the display will tell you what to do to enter BIOS. It may flash by quickly)<br/><br/>Once booted:<br/><br/>21) At the YUMI MultiBoot USB screen<br/><br/>22) Select System Tools<br/>(press Enter)<br/><br/>23) Select System Rescue CD<br/>(press Enter)<br/><br/>24) Select "#1 Default Boot Options"<br/>(first in the list)<br/>(press Enter)<br/><br/>(messages scroll past)<br/>(patience)<br/><br/>25) If it stops at the "Load Keymap" prompt, just press Enter<br/><br/>If everything goes well, you should be at a command prompt:<br/><br/>root@sysresccd /root %<br/><br/>26) Now you will type commands with a keyboard connected to the PBX:<br/><br/>fsck -y /dev/sda1<br/>(press Enter)<br/>(wait for the prompt to return)<br/><br/>fsck -y /dev/sda2<br/>(press Enter)<br/>(wait for the prompt to return)<br/><br/>fsck -y /dev/sda5<br/>(press Enter)<br/>(wait for the prompt to return)<br/>(NOTE!!! This is the main partition and can take awhile to clean up. Patience is HIGHLY recommended at this point)<br/><br/>Once the prompt returns Shutdown the PBX with this command:<br/><br/>shutdown -h now<br/><br/>After it has shutdown, remove the USB dongle and power up the PBX.<br/>Keep a monitor attached to watch.<br/><br/>If everything has gone correctly, you should be at the login prompt.<br/>Connect to the PBX with the web browser and attempt to login.		3) Insert a formated(FAT32), 1GBSB Drive to your PC<br/><br/>4) Double click on YUMI-0.0.2.8.exe<br/><br/>5) If a Security Warning pops up, click [Run]<br/><br/>6) License agreement<br/>Click [I Agree]<br/><br/>7) YUMI Setup Dialog<br/>Click the drop down list in the upper left<br/>Select the Drive letter of your USB Drive<br/><br/>8) In the upper right corner Select Format Drive (Erase Content)<br/><br/>9) From the list box under Step 2, scroll down to:<br/>System Rescue CD and highlight it.<br/><br/>10) Click the [Browse] button near the lower right corner<br/>Select the file:<br/>systemrescuecd-x86-2.3.1.iso<br/>and click [Open]<br/><br/>11) Click the [Create] button at the bottom of the dialog<br/><br/>12) Click [Yes] to perform listed actions<br/><br/>13) Wait about four (4) minutes<br/><br/>14) At the Installation Complete Dialog<br/>Make sure that there are no errors listed in the green text<br/>Click [Next]<br/><br/>15) At the "Would you like to add more ISOs/Distros Now?" question,<br/>Click [No]<br/><br/>16) At the dancing penguin dialog, click [Finish]<br/><br/>17) Eject the USB Drive<br/><br/>18) Insert USB Dongle into the PBX<br/><br/>19) Power the PBX on<br/><br/>20) Enter the BIOS and ensure the PBX is set to Boot from USB (This may be by pressing the Delete key or F2 or F3 key at the right time, the display will tell you what to do to enter BIOS. It may flash by quickly)<br/><br/>Once booted:<br/><br/>21) At the YUMI MultiBoot USB screen<br/><br/>22) Select System Tools<br/>(press Enter)<br/><br/>23) Select System Rescue CD<br/>(press Enter)<br/><br/>24) Select "#1 Default Boot Options"<br/>(first in the list)<br/>(press Enter)<br/><br/>(messages scroll past)<br/>(patience)<br/><br/>25) If it stops at the "Load Keymap" prompt, just press Enter<br/><br/>If everything goes well, you should be at a command prompt:<br/><br/>root@sysresccd /root %<br/><br/>26) Now you will type commands with a keyboard connected to the PBX:<br/><br/>fsck -y /dev/sda1<br/>(press Enter)<br/>(wait for the prompt to return)<br/><br/>fsck -y /dev/sda2<br/>(press Enter)<br/>(wait for the prompt to return)<br/><br/>fsck -y /dev/sda5<br/>(press Enter)<br/>(wait for the prompt to return)<br/>(NOTE!!! This is the main partition and can take awhile to clean up. Patience is HIGHLY recommended at this point)<br/><br/>Once the prompt returns Shutdown the PBX with this command:<br/><br/>shutdown -h now<br/><br/>After it has shutdown, remove the USB dongle and power up the PBX.<br/>Keep a monitor attached to watch.<br/><br/>If everything has gone correctly, you should be at the login prompt.<br/>Connect to the PBX with the web browser and attempt to login.

Mike Lunn at 22:02, 9 June 2015

2015-06-09T22:02:21Z

← Older revision		Revision as of 22:02, 9 June 2015
Line 1:		Line 1:
	USB Recovery Dongle Instructions:<br/>---------------------------------<br/><br/>1) Go to this website<br/>[http://www.ipitomy.com/webrelease/USB_Disk/rescue_disk/ http://www.ipitomy.com/webrelease/USB_Disk/rescue_disk/]<br/>and download the two files<br/>systemrescuecd-x86-2.3.1.iso<br/>YUMI-0.0.2.8.exe~~<br/><br/>~~2) Copy the two (2) files into the same directory.~~<br/><br/>~~3) Insert a formated, 1GBSB Drive to your PC<br/><br/>4) Double click on YUMI-0.0.2.8.exe<br/><br/>5) If a Security Warning pops up, click [Run]<br/><br/>6) License agreement<br/>Click [I Agree]<br/><br/>7) YUMI Setup Dialog<br/>Click the drop down list in the upper left<br/>Select the Drive letter of your USB Drive<br/><br/>8) In the upper right corner Select Format Drive (Erase Content)<br/><br/>9) From the list box under Step 2, scroll down to:<br/>System Rescue CD and highlight it.<br/><br/>10) Click the [Browse] button near the lower right corner<br/>Select the file:<br/>systemrescuecd-x86-2.3.1.iso<br/>and click [Open]<br/><br/>11) Click the [Create] button at the bottom of the dialog<br/><br/>12) Click [Yes] to perform listed actions<br/><br/>13) Wait about four (4) minutes<br/><br/>14) At the Installation Complete Dialog<br/>Make sure that there are no errors listed in the green text<br/>Click [Next]<br/><br/>15) At the "Would you like to add more ISOs/Distros Now?" question,<br/>Click [No]<br/><br/>16) At the dancing penguin dialog, click [Finish]<br/><br/>17) Eject the USB Drive<br/><br/>18) Insert USB Dongle into the PBX<br/><br/>19) Power the PBX on<br/><br/>20) Enter the BIOS and ensure the PBX is set to Boot from USB (This may be by pressing the Delete key or F2 or F3 key at the right time, the display will tell you what to do to enter BIOS. It may flash by quickly)<br/><br/>Once booted:<br/><br/>21) At the YUMI MultiBoot USB screen<br/><br/>22) Select System Tools<br/>(press Enter)<br/><br/>23) Select System Rescue CD<br/>(press Enter)<br/><br/>24) Select "#1 Default Boot Options"<br/>(first in the list)<br/>(press Enter)<br/><br/>(messages scroll past)<br/>(patience)<br/><br/>25) If it stops at the "Load Keymap" prompt, just press Enter<br/><br/>If everything goes well, you should be at a command prompt:<br/><br/>root@sysresccd /root %<br/><br/>26) Now you will type commands with a keyboard connected to the PBX:<br/><br/>fsck -y /dev/sda1<br/>(press Enter)<br/>(wait for the prompt to return)<br/><br/>fsck -y /dev/sda2<br/>(press Enter)<br/>(wait for the prompt to return)<br/><br/>fsck -y /dev/sda5<br/>(press Enter)<br/>(wait for the prompt to return)<br/>(NOTE!!! This is the main partition and can take awhile to clean up. Patience is HIGHLY recommended at this point)<br/><br/>Once the prompt returns Shutdown the PBX with this command:<br/><br/>shutdown -h now<br/><br/>After it has shutdown, remove the USB dongle and power up the PBX.<br/>Keep a monitor attached to watch.<br/><br/>If everything has gone correctly, you should be at the login prompt.<br/>Connect to the PBX with the web browser and attempt to login.		USB Recovery Dongle Instructions:<br/>---------------------------------<br/><br/>1) Go to this website<br/>[http://www.ipitomy.com/webrelease/USB_Disk/rescue_disk/ http://www.ipitomy.com/webrelease/USB_Disk/rescue_disk/]<br/>and download the two files<br/>systemrescuecd-x86-2.3.1.iso<br/>YUMI-0.0.2.8.exe
			2) Copy the two (2) files into the same directory.
			3) Insert a formated(FAT32), 1GBSB Drive to your PC<br/><br/>4) Double click on YUMI-0.0.2.8.exe<br/><br/>5) If a Security Warning pops up, click [Run]<br/><br/>6) License agreement<br/>Click [I Agree]<br/><br/>7) YUMI Setup Dialog<br/>Click the drop down list in the upper left<br/>Select the Drive letter of your USB Drive<br/><br/>8) In the upper right corner Select Format Drive (Erase Content)<br/><br/>9) From the list box under Step 2, scroll down to:<br/>System Rescue CD and highlight it.<br/><br/>10) Click the [Browse] button near the lower right corner<br/>Select the file:<br/>systemrescuecd-x86-2.3.1.iso<br/>and click [Open]<br/><br/>11) Click the [Create] button at the bottom of the dialog<br/><br/>12) Click [Yes] to perform listed actions<br/><br/>13) Wait about four (4) minutes<br/><br/>14) At the Installation Complete Dialog<br/>Make sure that there are no errors listed in the green text<br/>Click [Next]<br/><br/>15) At the "Would you like to add more ISOs/Distros Now?" question,<br/>Click [No]<br/><br/>16) At the dancing penguin dialog, click [Finish]<br/><br/>17) Eject the USB Drive<br/><br/>18) Insert USB Dongle into the PBX<br/><br/>19) Power the PBX on<br/><br/>20) Enter the BIOS and ensure the PBX is set to Boot from USB (This may be by pressing the Delete key or F2 or F3 key at the right time, the display will tell you what to do to enter BIOS. It may flash by quickly)<br/><br/>Once booted:<br/><br/>21) At the YUMI MultiBoot USB screen<br/><br/>22) Select System Tools<br/>(press Enter)<br/><br/>23) Select System Rescue CD<br/>(press Enter)<br/><br/>24) Select "#1 Default Boot Options"<br/>(first in the list)<br/>(press Enter)<br/><br/>(messages scroll past)<br/>(patience)<br/><br/>25) If it stops at the "Load Keymap" prompt, just press Enter<br/><br/>If everything goes well, you should be at a command prompt:<br/><br/>root@sysresccd /root %<br/><br/>26) Now you will type commands with a keyboard connected to the PBX:<br/><br/>fsck -y /dev/sda1<br/>(press Enter)<br/>(wait for the prompt to return)<br/><br/>fsck -y /dev/sda2<br/>(press Enter)<br/>(wait for the prompt to return)<br/><br/>fsck -y /dev/sda5<br/>(press Enter)<br/>(wait for the prompt to return)<br/>(NOTE!!! This is the main partition and can take awhile to clean up. Patience is HIGHLY recommended at this point)<br/><br/>Once the prompt returns Shutdown the PBX with this command:<br/><br/>shutdown -h now<br/><br/>After it has shutdown, remove the USB dongle and power up the PBX.<br/>Keep a monitor attached to watch.<br/><br/>If everything has gone correctly, you should be at the login prompt.<br/>Connect to the PBX with the web browser and attempt to login.

Mike Lunn at 18:34, 9 February 2015

2015-02-09T18:34:54Z

← Older revision		Revision as of 18:34, 9 February 2015
Line 1:		Line 1:
	USB Recovery Dongle Instructions:<br/>---------------------------------<br/><br/>1) Go to this website<br/>[http://www.ipitomy.com/webrelease/USB_Disk/rescue_disk/ http://www.ipitomy.com/webrelease/USB_Disk/rescue_disk/]<br/>and download the two files<br/>systemrescuecd-x86-2.3.1.iso<br/>YUMI-0.0.2.8.exe<br/><br/>2) Copy the two (2) files into the same directory.<br/><br/>3) Insert a formated, 1GBSB Drive to your PC<br/><br/>4) Double click on YUMI-0.0.2.8.exe<br/><br/>5) If a Security Warning pops up, click [Run]<br/><br/>6) License agreement<br/>Click [I Agree]<br/><br/>7) YUMI Setup Dialog<br/>Click the drop down list in the upper left<br/>Select the Drive letter of your USB Drive<br/><br/>8) In the upper right corner Select Format Drive (Erase Content)<br/><br/>9) From the list box under Step 2, scroll down to:<br/>System Rescue CD and highlight it.<br/><br/>10) Click the [Browse] button near the lower right corner<br/>Select the file:<br/>systemrescuecd-x86-2.3.1.iso<br/>and click [Open]<br/><br/>11) Click the [Create] button at the bottom of the dialog<br/><br/>12) Click [Yes] to perform listed actions<br/><br/>13) Wait about four (4) minutes<br/><br/>14) At the Installation Complete Dialog<br/>Make sure that there are no errors listed in the green text<br/>Click [Next]<br/><br/>15) At the "Would you like to add more ISOs/Distros Now?" question,<br/>Click [No]<br/><br/>16) At the dancing penguin dialog, click [Finish]<br/><br/>17) Eject the USB Drive<br/><br/>18) Insert USB Dongle into the PBX<br/><br/>19) Power the PBX on<br/><br/>20) Enter the BIOS and ensure the PBX is set to Boot from USB<br/><br/>Once booted:<br/><br/>21) At the YUMI MultiBoot USB screen<br/><br/>22) Select System Tools<br/>(press Enter)<br/><br/>23) Select System Rescue CD<br/>(press Enter)<br/><br/>24) Select "#1 Default Boot Options"<br/>(first in the list)<br/>(press Enter)<br/><br/>(messages scroll past)<br/>(patience)<br/><br/>25) If it stops at the "Load Keymap" prompt, just press Enter<br/><br/>If everything goes well, you should be at a command prompt:<br/><br/>root@sysresccd /root %<br/><br/>26) Now you will type commands with a keyboard connected to the PBX:<br/><br/>fsck -y /dev/sda1<br/>(press Enter)<br/>(wait for the prompt to return)<br/><br/>fsck -y /dev/sda2<br/>(press Enter)<br/>(wait for the prompt to return)<br/><br/>fsck -y /dev/sda5<br/>(press Enter)<br/>(wait for the prompt to return)<br/>(NOTE!!! This is the main partition and can take awhile to clean up. Patience is HIGHLY recommended at this point)<br/><br/>Once the prompt returns Shutdown the PBX with this command:<br/><br/>shutdown -h now<br/><br/>After it has shutdown, remove the USB dongle and power up the PBX.<br/>Keep a monitor attached to watch.<br/><br/>If everything has gone correctly, you should be at the login prompt.<br/>Connect to the PBX with the web browser and attempt to login.		USB Recovery Dongle Instructions:<br/>---------------------------------<br/><br/>1) Go to this website<br/>[http://www.ipitomy.com/webrelease/USB_Disk/rescue_disk/ http://www.ipitomy.com/webrelease/USB_Disk/rescue_disk/]<br/>and download the two files<br/>systemrescuecd-x86-2.3.1.iso<br/>YUMI-0.0.2.8.exe<br/><br/>2) Copy the two (2) files into the same directory.<br/><br/>3) Insert a formated, 1GBSB Drive to your PC<br/><br/>4) Double click on YUMI-0.0.2.8.exe<br/><br/>5) If a Security Warning pops up, click [Run]<br/><br/>6) License agreement<br/>Click [I Agree]<br/><br/>7) YUMI Setup Dialog<br/>Click the drop down list in the upper left<br/>Select the Drive letter of your USB Drive<br/><br/>8) In the upper right corner Select Format Drive (Erase Content)<br/><br/>9) From the list box under Step 2, scroll down to:<br/>System Rescue CD and highlight it.<br/><br/>10) Click the [Browse] button near the lower right corner<br/>Select the file:<br/>systemrescuecd-x86-2.3.1.iso<br/>and click [Open]<br/><br/>11) Click the [Create] button at the bottom of the dialog<br/><br/>12) Click [Yes] to perform listed actions<br/><br/>13) Wait about four (4) minutes<br/><br/>14) At the Installation Complete Dialog<br/>Make sure that there are no errors listed in the green text<br/>Click [Next]<br/><br/>15) At the "Would you like to add more ISOs/Distros Now?" question,<br/>Click [No]<br/><br/>16) At the dancing penguin dialog, click [Finish]<br/><br/>17) Eject the USB Drive<br/><br/>18) Insert USB Dongle into the PBX<br/><br/>19) Power the PBX on<br/><br/>20) Enter the BIOS and ensure the PBX is set to Boot from USB (This may be by pressing the Delete key or F2 or F3 key at the right time, the display will tell you what to do to enter BIOS. It may flash by quickly)<br/><br/>Once booted:<br/><br/>21) At the YUMI MultiBoot USB screen<br/><br/>22) Select System Tools<br/>(press Enter)<br/><br/>23) Select System Rescue CD<br/>(press Enter)<br/><br/>24) Select "#1 Default Boot Options"<br/>(first in the list)<br/>(press Enter)<br/><br/>(messages scroll past)<br/>(patience)<br/><br/>25) If it stops at the "Load Keymap" prompt, just press Enter<br/><br/>If everything goes well, you should be at a command prompt:<br/><br/>root@sysresccd /root %<br/><br/>26) Now you will type commands with a keyboard connected to the PBX:<br/><br/>fsck -y /dev/sda1<br/>(press Enter)<br/>(wait for the prompt to return)<br/><br/>fsck -y /dev/sda2<br/>(press Enter)<br/>(wait for the prompt to return)<br/><br/>fsck -y /dev/sda5<br/>(press Enter)<br/>(wait for the prompt to return)<br/>(NOTE!!! This is the main partition and can take awhile to clean up. Patience is HIGHLY recommended at this point)<br/><br/>Once the prompt returns Shutdown the PBX with this command:<br/><br/>shutdown -h now<br/><br/>After it has shutdown, remove the USB dongle and power up the PBX.<br/>Keep a monitor attached to watch.<br/><br/>If everything has gone correctly, you should be at the login prompt.<br/>Connect to the PBX with the web browser and attempt to login.

Mike Lunn: Created page with "USB Recovery Dongle Instructions:
---------------------------------

1) Go to this website
[http://www.ipitomy.com/webrelease/USB_Disk/rescue_disk/ http://www...."

2013-02-15T20:41:18Z

Created page with "USB Recovery Dongle Instructions: --------------------------------- 1) Go to this website [http://www.ipitomy.com/webrelease/USB_Disk/rescue_disk/ http://www...."

New page

USB Recovery Dongle Instructions: --------------------------------- 1) Go to this website [http://www.ipitomy.com/webrelease/USB_Disk/rescue_disk/ http://www.ipitomy.com/webrelease/USB_Disk/rescue_disk/] and download the two files systemrescuecd-x86-2.3.1.iso YUMI-0.0.2.8.exe 2) Copy the two (2) files into the same directory. 3) Insert a formated, 1GBSB Drive to your PC 4) Double click on YUMI-0.0.2.8.exe 5) If a Security Warning pops up, click [Run] 6) License agreement Click [I Agree] 7) YUMI Setup Dialog Click the drop down list in the upper left Select the Drive letter of your USB Drive 8) In the upper right corner Select Format Drive (Erase Content) 9) From the list box under Step 2, scroll down to: System Rescue CD and highlight it. 10) Click the [Browse] button near the lower right corner Select the file: systemrescuecd-x86-2.3.1.iso and click [Open] 11) Click the [Create] button at the bottom of the dialog 12) Click [Yes] to perform listed actions 13) Wait about four (4) minutes 14) At the Installation Complete Dialog Make sure that there are no errors listed in the green text Click [Next] 15) At the "Would you like to add more ISOs/Distros Now?" question, Click [No] 16) At the dancing penguin dialog, click [Finish] 17) Eject the USB Drive 18) Insert USB Dongle into the PBX 19) Power the PBX on 20) Enter the BIOS and ensure the PBX is set to Boot from USB Once booted: 21) At the YUMI MultiBoot USB screen 22) Select System Tools (press Enter) 23) Select System Rescue CD (press Enter) 24) Select "#1 Default Boot Options" (first in the list) (press Enter) (messages scroll past) (patience) 25) If it stops at the "Load Keymap" prompt, just press Enter If everything goes well, you should be at a command prompt: root@sysresccd /root % 26) Now you will type commands with a keyboard connected to the PBX: fsck -y /dev/sda1 (press Enter) (wait for the prompt to return) fsck -y /dev/sda2 (press Enter) (wait for the prompt to return) fsck -y /dev/sda5 (press Enter) (wait for the prompt to return) (NOTE!!! This is the main partition and can take awhile to clean up. Patience is HIGHLY recommended at this point) Once the prompt returns Shutdown the PBX with this command: shutdown -h now After it has shutdown, remove the USB dongle and power up the PBX. Keep a monitor attached to watch. If everything has gone correctly, you should be at the login prompt. Connect to the PBX with the web browser and attempt to login.

USB Recovery Dongle - Revision history

Mike Lunn at 22:04, 9 June 2015

Mike Lunn at 22:02, 9 June 2015

Mike Lunn at 22:02, 9 June 2015

Mike Lunn at 18:34, 9 February 2015

Mike Lunn: Created page with "USB Recovery Dongle Instructions:---------------------------------1) Go to this website[http://www.ipitomy.com/webrelease/USB_Disk/rescue_disk/ http://www...."

Mike Lunn: Created page with "USB Recovery Dongle Instructions:
---------------------------------

1) Go to this website
[http://www.ipitomy.com/webrelease/USB_Disk/rescue_disk/ http://www...."