RTX DECT Phone

From IPitomy Wiki
Revision as of 15:11, 2 July 2014 by Mike Lunn (talk | contribs)
Jump to navigation Jump to search

Configuration of RTX SIP DECT base and Handsets And the Ipitomy PBX

NOTE: The base range of the typical DECT unit is 300ft, but does not take into account walls and other points of interference.


Section 1) How to add a Ipitomy SIP server

Section 2) How to register a handset



Hardware required equipment
This section describes what hardware is needed to execute the guideline. You need the following to perform a registration of a handset to a base station (gateway):
1 x base station
1 x handset
1 x Ethernet cable
1 x PC connected to the LAN, VLAN or WAN

File:RTX SIP Dect 1.pngFile:RTX SIP Dect 2.pngFile:RTX SIP Dect 3.pngFile:RTX SIP Dect 4.png
 
    

Plug the Ethernet cable into the base station and connect the other end of the cable to your network (LAN, VLAN or WAN ). The base station is supplied via the Ethernet cable (PoE). PC must be connected to the same network as the base station.

If your network doesn’t support PoE (Power over Ethernet), then a PoE adaptor must be used.

File:RTX SIP Dect 5.png

 

Software required equipment


This section describes what software is needed. You will need the following to access the web configuration interface on the base station:
Windows Internet explorer installed on the PC

Add Ipitomy server
This section describes how to add a SIP server to the base station (gateway).
Step 1: Determine the IP address of the base station
Read the MAC address on the labels on the back side of the base station
Press “Menu” key on the handset followed by the keys: *47* to get the handset into the base station search mode.
Use the cursor down/up to select the base station which match the MAC address read under item 1, and use the IP address listed below the MAC address.
Open  Windows Internet Explore on the computer and type in the IP address of the base

File:RTX SIP Dect 6.png


File:RTX SIP Dect 7.png


 Step 2: Type in the “Username” and “Password” when prompted. The default username and password is “admin”.

Step 3) A SIP server must be configured on the base before handsets can be registered to the base. To add a SIP server, select sheet “Server” and click the link “Add server”.


File:RTX SIP Dect 8.png

 
Step 4) Fill out the displayed form and click “Save”. In the shown example we configure a Ipitomy SIP server located on the IP address 192.168.50.77 and no Outbound proxy is used. Set “NAT adaption” if the base station is located  behind a NAT router. It is also possible to type in the URL’s direct, i.e. like “sipphone.com”


File:RTX SIP Dect 9.png
 
Please notice: The new Ipitomy server is displayed to the left when it is successfully saved.

File:RTX SIP Dect 10.png
 

Register handset to base


Note: Prior to this step you should create an Extension in the Ipitomy PBX for each Handset. These stations will use Open Licenses. And you should set the Phone Model as "Generic". Make note of the Station number and the Extension SIP password. The Extension SIP password may be found under Advanced when you edit the Extensions settings

File:RTX SIP Dect 21.png


This section describes how to register the wireless handset to the base station.
Please notice: Minimum one SIP server must be registered to the base (system), otherwise a handset cannot be registered to the system. Please see chapter “Add server”.

Step 1: Open  Windows Internet Explore on the computer and type in the IP address of the base. Press “Enter” to access the base.

File:RTX SIP Dect 6.png

File:RTX SIP Dect 7.png


 

 Step 2: Type in the “Username” and “Password” when prompted. The default username and password is “admin”.

Step 3: Select sheet “Extensions” and click “Add extension”

File:RTX SIP Dect 11.png


 

Step 4: Fill out the form and click “Save”. In the example below we add the extension “3020” and this SIP account got the same number as “Authentication User Name” and “Password”. The “Server 1” is selected as server for this extension.

File:RTX SIP Dect 12.png
 

IMPORTANT: Step 5: Set a Check mark on the extension which shall be assigned to the handset you want to register and click “Register handset (s)”. The base is now open for handset registrations for 5 minutes.

File:RTX SIP Dect 13.png

Step 6: Start the registration procedure on the handset by following step “a” to “d” below.

 a) Select main menu “Connectivity”

File:RTX SIP Dect 14.png







 b)  Select menu ”Register”

File:RTX SIP Dect 15.png





 c)  Type in the “AC code” and press “OK” to start the registration. The default AC code is “0000”.

File:RTX SIP Dect 16.png





 d) After a while the handset is registered, and the idle display is shown.


File:RTX SIP Dect 17.png








Please notice:  The unique handset IPEI is displayed on sheet “Extensions” when the handset is successfully registered. The web page must be manually updated by pressing “F5” to see that the handset is registered; otherwise the handset IPEI (International Portable Equipment Identity) isn’t displayed on the web page.


File:RTX SIP Dect 18.png
 


You can also check status of the Handsets from the Monitoring page of the PBX.


File:RTX SIP Dect 19.png